Juno Mould
Exclusive to Myka Candles & Moulds and hand-poured to order in Australia using premium platinum-cure silicone. (Up to 1 week processing time)
Introducing the largest pregnancy candle IN THE WORLD. This one-of-a-kind handmade mould is crafted from platinum-cure silicone using a 3D printed design. To use, simply start by piercing a hole through the centre of the neck area where you want the wick to come out. Thread the wick into the hole and align the two sides of the mould together before securing with clips. Pour in melted wax and allow it to cure overnight before carefully unmoulding the candle.
Please note that this mould is intentionally cut to make unmoulding easier. This, in turn, will leave a seam line on the candle, but it's appearance can be minimized by ensuring that the opening of the mould is aligned as perfectly as possible before pouring in your wax.
Platinum-cure silicone is known for its durability and tear-resistance. It can withstand high temperatures up to 230°C, but it is not recommended to expose them to excessive heat for long periods of time. In comparison to regular silicone moulds, moulds made with platinum-cure silicone are more long-lasting and has a shelf life of more than 30 years.
Specifications
Finished product: 22cm (H) x 13cm (W) x 11cm (L)
Wax volume: 1090g
Cotton wick recommendation: 15 ply
All measurements are approximate and will vary depending on the type of wax used and how much fragrance oil is added.
Mould Perfomance & Storage
The physical life of the mould depends on how you use it (materials cast, frequency, etc.). Casting abrasive materials such as concrete can quickly erode mould detail, while casting non-abrasive materials, such as wax, will not affect mould detail. Do not over-stretch or use any abrasive tools or fingernails when demoulding.
Before storing, the mould should be cleaned with a soap solution and fully dry. Two part moulds should be assembled. Moulds should be stored on a level surface in a cool, dry environment to maintain its original shape.
Disclaimer: This design is 3D printed using PLA filament and therefore may have some print lines on the finished product. Our custom moulds are poured and trimmed by hand and may have some minor exterior imperfections.
How To Use
Acrylic PVC Candle Moulds:
To use this candle mould, simply start by threading the wick through the center of the mould and securing it in place with a wick holder. Use blu tack to cover the wick hole to prevent leakage before pouring melted wax into the mould. Depending on the type of wax you are using, you may need to perform a second pour to even out the surface of the candle. Allow your candle to cure overnight before carefully unmoulding it. If the candle gets stuck, squeeze around the mould to release the candle from the sides.
Silicone Candle Moulds:
To use our candle moulds, simply start by threading the wick through the center of the mould and securing it in place with a wick holder. Then, pour in your melted wax and let it cool until it hardens. Depending on the type of wax you are using, you may need to perform a second pour to even out the surface of the candle. Allow your candle to cure overnight before carefully unmoulding it.
Concrete Trays & Vessels:
To make the most of your vessel mould, follow these steps:
- Preparation: Begin by gathering your selected material and ensure it's mixed according to the manufacturer's instructions.
- Pouring: Carefully fill the mould with your chosen material, ensuring it reaches the top.
- Air Bubble Removal: For a smoother finish, gently tap the mould on a sturdy surface to encourage any trapped air bubbles to rise to the surface.
- Curing: Adhere to the recommended curing time for your chosen material.
- Demoulding: Once the material has set and cured, carefully flex and remove the mould to unveil your creation.
- If your tray or vessel will be used for candles, it is vital to seal it with a heat-resistant sealer. Apply at least two coats to both the interior and exterior of the vessel. Ensure the sealant is fully dry before pouring in the wax.
Shipping
Standard (Australia):
- 3-7 business days
- $12 shipping fee
Express (Australia)
- 1-3 business days
- $17
Standard (New Zealand)
- 4-14 business days
- $20
DHL Express (International)
- 3-7 business days via DHL Express
- Calculated based on location and weight
Returns & Refunds
Parcel Claims:
Report missing or damaged items within 24 hours of delivery to be eligible for store credit or a replacement. Include proof of purchase and photographic evidence. Contact us at info@mykacandlesandmoulds.com.
Moulds Disclaimer:
Expect slight imperfections in our handmade silicone moulds, which won't affect the final product. For unlevel moulds, adjust using simple supports.
Exchanges/Refunds:
No alterations, cancellations, exchanges, or refunds after purchase except as covered under parcel claims.
Lost/Damaged Parcels:
If a package is lost or damaged, contact us immediately for assistance with a claim.
For detailed information on our policies, please visit our full Returns & Refunds Policy.
